Welcome to Bafinasa official website!

Mustard Yellow Tiered Boho Maxi Dress Women's

Source:News / Time:2026-11-14

The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed. Nothing in this style is hard to sew. It is hard to sew consistently, which is a different problem and a more expensive one. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. A Mustard Yellow Tiered Boho Maxi Dress Women's reads as a short brief until the pattern is cut, and the shape only holds when the tier seam, the waist seam and the hem allowance are settled together.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. Wash the sample once before approval. Some cloths lose two centimetres of length and gain a surface that was not on the swatch. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Drawstrings are threaded after washing the sample. A cotton cord that shrinks will pucker the channel. Loose weaves need a French or flat-felled seam. A plain overlock shows at the slit and at the hem.

The tiered is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. When the brief names the tiered, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain.

Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the tier seam to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. We fit the middle size on a live model, then check the smallest and the largest on real bodies, not on the form.

What goes on the spec sheet

Shella 90 to 120 gsm cotton voile, or a viscose crinkle for movement, swatch-approved, one dye lot for bulk
Bodyboho maxi dress
Lengthmaxi
Colourwayyellow
Liningfully lined, bagged hem
Closureinvisible centre-back zip
Size runS-XL (4 sizes) for the test
Sample lead time12-18 days after spec sign-off
MOQ100 pcs per colour

Failure points worth designing out

  • Cord channels sewn too narrow, so the drawstring jams after the first wash.
  • Tier seams pressed one way, making a ridge that reads through a light print.
  • The sample passes on the form and fails on a body: the waist sits high, the armhole cuts, or the sweep is short. Fit on a real model before approving anything.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule. In bulk the failures cluster: skipped stitches on the tier seam, shading between panels, and hems that go wavy after pressing. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork.

Changes we can make at sample stage

  • Print: stock, custom digital, or placement-matched at the front.
  • Neckline: square with ties, V with a modesty panel, or elasticated.
  • Sleeve: blouson, flutter, or straight with a ruffle.
  • Tier count and depth, priced per configuration.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top