For Women Sage Green Flowy Boho Maxi Dress
Written down, the request is for women sage green flowy boho maxi dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. It helps to separate what the customer sees from what the factory feels. The outside is cotton voile or viscose crinkle in green, the inside is structure, and the two have to agree on the same sample. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch.
Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. We start with cotton voile or viscose crinkle on the first sample and keep one alternative on the table, then compare how each hangs on a moving model rather than on the form. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Under 200 gsm, plan to interface the tier seam. Without it, the seam ridge shows through at the first press.
Construction notes
Most of the handwork sits in a handful of steps, and each one has a right order. Drawstrings are threaded after washing the sample. A cotton cord that shrinks will pucker the channel. Trims and tassels go on after the first fitting. They change the weight of the hem and how the skirt falls. Measure a maxi from the waist once the skirt is gathered, not from the shoulder on the flat.
The tier line is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. The tier line reads as a design choice and behaves as a construction one. It changes the seam order, and sometimes the closure.
Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the tier seam. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the tier seam to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.
Spec sheet, line by line
| Shell | a 90 to 120 gsm cotton voile, or a viscose crinkle for movement, swatch-approved, one dye lot for bulk |
| Body | boho maxi dress |
| Length | maxi |
| Colourway | green |
| Lining | unlined with faced seams |
| Closure | invisible centre-back zip |
| Size run | S-3XL graded to your sheet |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 150 pcs per style |
The places this usually goes wrong
- Print placement ignored at the centre front, so the motif lands off-centre in bulk.
- Tier seams pressed one way, making a ridge that reads through a light print.
- Gather ratios left to the operator, so two sizes of the same tier look different.
- A cheap hem shows: three centimetres with a clean catch-stitch reads expensive, one centimetre overlocked reads fast fashion.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
Packing flat or on hangers changes the crease pattern. Decide before the cartons are ordered. Set stitch density at 12 to 14 per inch on woven seams and check it at the machine, not on the finished garment. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.
What we can change for you
- Neckline: square with ties, V with a modesty panel, or elasticated.
- Sleeve: blouson, flutter, or straight with a ruffle.
- Tier count and depth, priced per configuration.
- Print: stock, custom digital, or placement-matched at the front.
- Private label: woven label, care label and hangtag to your artwork.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.
Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.