Welcome to Bafinasa official website!

White Off Shoulder Boho Maxi Dress Women's

Source:News / Time:2026-11-14

It helps to separate what the customer sees from what the factory feels. The outside is cotton voile or viscose crinkle in white, the inside is structure, and the two have to agree on the same sample. Samples for this garment rarely fail on design. They fail on a measurement that was never written down, and a cloth that behaved differently from the swatch. Written down, the request is white off shoulder boho maxi dress women's: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish.

Ask for weight in gsm and composition as percentages, not trade names. Trade names do not travel well between mills. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Request a shrink test on the actual dye lot. Half a percent across a maxi is visible to the customer and invisible on the sheet.

Structure and seams

The build follows the same order on every size. These are the steps where the shape is won or lost. Lining a sheer maxi is a design decision, not a default. State the lining length separately or it will be made to the shell. Tiered skirts need every tier cut on the same grain and the gather ratio written down. Otherwise the volume changes between sizes. Loose weaves need a French or flat-felled seam. A plain overlock shows at the slit and at the hem.

The off shoulder is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample. Check the off shoulder after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.

Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the tier seam. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the tier seam to move at different rates. Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample.

The sheet we need before costing

Shella 90 to 120 gsm cotton voile, or a viscose crinkle for movement, swatch-approved, one dye lot for bulk
Bodyboho maxi dress
Lengthmaxi
Colourwaywhite
Liningbodice lined, skirt lined
Closurestretch panel, no zip
Size runS-3XL graded to your sheet
Sample lead time12-18 days after spec sign-off
MOQ50 pcs sample order

The places this usually goes wrong

  • Print placement ignored at the centre front, so the motif lands off-centre in bulk.
  • Cord channels sewn too narrow, so the drawstring jams after the first wash.
  • Gather ratios left to the operator, so two sizes of the same tier look different.
  • Two rolls under the same colour name will not match. Buy one lot, keep the roll reference with the order, and cut the run from it.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.

Schedule an in-line check after the tier seam goes on. Catching a rotation there costs minutes; catching it at final costs the order. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. AQL 2.5 on major and 4.0 on minor is a reasonable default here. Write it into the order so the inspection has a rule.

What we can change for you

  • Print: stock, custom digital, or placement-matched at the front.
  • Sleeve: blouson, flutter, or straight with a ruffle.
  • Shell swap: the same block in a lighter or heavier cloth, priced separately.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The proto is usually made in stock cloth. Do not judge the hand from it; judge the line. The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use.

Send the tech pack as a PDF with a measurement table, not as a photo with notes in a chat. Photos carry intent, tables carry production. If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top