Tassel Ties Long Sleeve Boho Maxi Dress
A Tassel Ties Long Sleeve Boho Maxi Dress reads as a short brief until the pattern is cut, and the shape only holds when the tier seam, the waist seam and the hem allowance are settled together. Written down, the request is tassel ties long sleeve boho maxi dress: a body, a length and a budget. Those three lines are enough to start a pattern, provided somebody writes the fourth line - the finish. There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.
Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes. Request a shrink test on the actual dye lot. Half a percent across a maxi is visible to the customer and invisible on the sheet. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded.
Structure and seams
The pattern sets the shape and the sewing protects it. A few steps decide whether it survives the third wash. Lining a sheer maxi is a design decision, not a default. State the lining length separately or it will be made to the shell. Tiered skirts need every tier cut on the same grain and the gather ratio written down. Otherwise the volume changes between sizes. Loose weaves need a French or flat-felled seam. A plain overlock shows at the slit and at the hem.
When the brief names the long sleeve, allow extra cloth and extra time: it is cut from a separate panel and has to be matched for grain. Check the long sleeve after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift.
Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the tier seam. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.
Specification, item by item
| Shell | a 90 to 120 gsm cotton voile, or a viscose crinkle for movement, swatch-approved, one dye lot for bulk |
| Body | boho maxi dress |
| Length | maxi |
| Colourway | buyer colourway, lab-dipped under two lights |
| Lining | half lined to the hip |
| Closure | covered button placket |
| Size run | S-XL (4 sizes) for the test |
| Sample lead time | 10-14 days on stock cloth |
| MOQ | 50 pcs sample order |
Where this style fails in production
- Cord channels sewn too narrow, so the drawstring jams after the first wash.
- Gather ratios left to the operator, so two sizes of the same tier look different.
- Tier seams pressed one way, making a ridge that reads through a light print.
- Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
- Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. Pressing is a step, not a rescue. A seam pressed open before the next one is sewn behaves differently from one pressed at the end.
Customisation that does not break the price
- Tier count and depth, priced per configuration.
- Print: stock, custom digital, or placement-matched at the front.
- Neckline: square with ties, V with a modesty panel, or elasticated.
- Sleeve: blouson, flutter, or straight with a ruffle.
- Shell swap: the same block in a lighter or heavier cloth, priced separately.
- Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.
The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder.
A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.
If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.