Welcome to Bafinasa official website!

Sage Green Tiered Ruffle Hem Tassel Boho Maxi Dress

Source:News / Time:2026-11-14

A Sage Green Tiered Ruffle Hem Tassel Boho Maxi Dress reads as a short brief until the pattern is cut, and the shape only holds when the tier seam, the waist seam and the hem allowance are settled together. It helps to separate what the customer sees from what the factory feels. The outside is cotton voile or viscose crinkle in green, the inside is structure, and the two have to agree on the same sample. This is a style that rewards a patient first sample. Every shortcut taken on the block comes back later as a return, a re-cut or a discount. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

The hand a buyer approves on a swatch is what bulk has to repeat. If the mill cannot repeat it, change the mill before the pattern is graded. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting. Request a shrink test on the actual dye lot. Half a percent across a maxi is visible to the customer and invisible on the sheet. Stretch is the quiet variable. Two percent elastane changes the grade rule, the seam type, and how the hem behaves after ten washes.

How it is built

Most of the handwork sits in a handful of steps, and each one has a right order. Drawstrings are threaded after washing the sample. A cotton cord that shrinks will pucker the channel. Measure a maxi from the waist once the skirt is gathered, not from the shoulder on the flat. Trims and tassels go on after the first fitting. They change the weight of the hem and how the skirt falls.

Check the ruffle after pressing, not before. Light cloth relaxes under steam and what looked balanced on the table can shift. The ruffle is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Grading is where the quiet failures happen. Four sizes from one block need the armhole, the waist and the tier seam to move at different rates. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the tier seam.

What goes on the spec sheet

Shella 90 to 120 gsm cotton voile, or a viscose crinkle for movement, swatch-approved, one dye lot for bulk
Bodyboho maxi dress
Lengthmaxi
Colourwaygreen
Liningfully lined, bagged hem
Closurestretch panel, no zip
Size runXS-2XL plus a curve block
Sample lead time15-20 days with handwork
MOQ100 pcs per colour

What to check before bulk

  • Tier seams pressed one way, making a ridge that reads through a light print.
  • Cord channels sewn too narrow, so the drawstring jams after the first wash.
  • Every detail placed by eye on the sample has to be measured on the pattern, or the size run drifts.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Keep one sealed bulk sample per colour. Six months later it is the only honest reference for a reorder. Lead time is normally 12 to 20 days for a first sample and 30 to 45 days for bulk, depending on stock cloth and handwork. Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem.

Changes we can make at sample stage

  • Neckline: square with ties, V with a modesty panel, or elasticated.
  • Print: stock, custom digital, or placement-matched at the front.
  • Tier count and depth, priced per configuration.
  • Sleeve: blouson, flutter, or straight with a ruffle.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.
  • Sizing: a four-size test run, a standard eight-size run, or a graded run to your own sheet.

Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there. Keep the approved pre-production sample sealed. It is the reference for the in-line check and for the reorder. Sampling runs in three steps: a proto to check proportion, a fit sample to check the body, and a pre-production sample cut from bulk cloth.

Confirm the ship window against the mill calendar and the holiday shutdown before the purchase order is signed. Ask for two samples when the cloth is new to us: one in the buyer cloth, one in our closest stock cloth. The comparison usually settles the price question.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top