Welcome to Bafinasa official website!

Tassel Ties Rust Bohemian Maxi Dress

Source:News / Time:2026-11-14

There is nothing experimental about this garment. The difficulty is discipline: the same four measurements decide fit on every size, and they have to be printed, not remembered. It helps to separate what the customer sees from what the factory feels. The outside is cotton voile or viscose crinkle, the inside is structure, and the two have to agree on the same sample. A Tassel Ties Rust Bohemian Maxi Dress can be made at almost any price. What changes is how long it keeps its line and how much of the making shows. The first conversation about this style is usually about length. The second, if the buyer is serious, is about the inside: lining, interlining, and where the seams are pressed.

Under 200 gsm, plan to interface the tier seam. Without it, the seam ridge shows through at the first press. Request a shrink test on the actual dye lot. Half a percent across a maxi is visible to the customer and invisible on the sheet. Lining is not a detail. A 65 to 75 gsm taffeta slides over the cloth; a cheap lining grabs it and the garment climbs when the wearer walks. Approve colour under two lights, D65 and warm indoor. A black that reads neutral in an office can read green under shop lighting.

Where the shape comes from

The build follows the same order on every size. These are the steps where the shape is won or lost. Lining a sheer maxi is a design decision, not a default. State the lining length separately or it will be made to the shell. Loose weaves need a French or flat-felled seam. A plain overlock shows at the slit and at the hem. Tiered skirts need every tier cut on the same grain and the gather ratio written down. Otherwise the volume changes between sizes.

If the tier line is central to the style, price a second sample with a simpler version. Volume often goes to the simpler one. The tier line is where the eye lands first, so it is also where a two-millimetre error shows. Set it from the pattern, not from the sample.

Get the fit model measurements in the same units as the spec. Mixed units are the most common cause of a rejected first sample. Tolerances belong on the sheet: plus or minus one centimetre on the body, half a centimetre on the tier seam. On this style the difference between a good and a poor fit is usually two centimetres at the waist seam, not a redesign.

Spec sheet, line by line

Shella 90 to 120 gsm cotton voile, or a viscose crinkle for movement, swatch-approved, one dye lot for bulk
Bodyboho maxi dress
Lengthmaxi
Colourwaybuyer colourway, lab-dipped under two lights
Liningbodice lined, skirt lined
Closureconcealed side zip
Size runS-XL (4 sizes) for the test
Sample lead time10-14 days on stock cloth
MOQ50 pcs sample order

The places this usually goes wrong

  • Print placement ignored at the centre front, so the motif lands off-centre in bulk.
  • Gather ratios left to the operator, so two sizes of the same tier look different.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.
  • Pressing decides the finish. A needle mark on a light cloth stays after QC, whatever the inspector does.

Measure ten pieces per size from the first bulk run. If the spread is wider than the tolerance, the cutting and not the sewing is the problem. Trims are ordered against confirmed quantity plus three percent. Short trims stop a line faster than short cloth. In bulk the failures cluster: skipped stitches on the tier seam, shading between panels, and hems that go wavy after pressing.

Customisation that does not break the price

  • Tier count and depth, priced per configuration.
  • Neckline: square with ties, V with a modesty panel, or elasticated.
  • Private label: woven label, care label and hangtag to your artwork.
  • Packing: flat-fold with tissue, hanger-ready, or a sealed bag per piece.

The fit sample is where the pattern is corrected. Changes after this point cost time, not only money. The pre-production sample has to be cut from the bulk lot, with the bulk trims, on the machine settings bulk will use. Photograph each stage on the same model and keep the photos with the spec sheet. Most disputes end there.

If the price has to come down, take it out of handwork before taking it out of the cloth. The customer notices the cloth first. A reorder is easier than a first order, provided the approved sample and the measurement sheet were kept together.

If you are developing this style, send us a tech pack, a photo or a reference garment and we will quote within 24 hours. Contact bafinasa@bafinasa.com or WhatsApp +86 13827222469.

Online customer service
WeChat contact
Customer service
Scan code to add Wechat (same mobile phone number)
Telephone consultation
Back to top